The 40 most recent of 131 complaints, exactly as filed with NHTSA. These are owners' own accounts and have not been verified.
Nov 16, 2026 · 165,200 miles · MO
Electrical system › Instrument panel › Speedometer/odometer
Odometer Fraud. The contact purchased a 2015 Mazda Mazda3. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a dealer sale. At the time of purchase, the mileage was 156,684, and at the time of registration, it was discovered that the mileage was 165,200.
NHTSA ID 11778287
Apr 15, 2026 · 180,000 miles · NJ
Back over prevention › Sensing system › Camera
The contact owns a 2015 Mazda Mazda3. The contact stated that while driving at various speeds, or while attempting to reverse, the rear camera flashed on and off for approximately five minutes and then started working as intended. No warning light was illuminated. The vehicle was repaired under the NHTSA Campaign Number: 23V487000 (BACK OVER PREVENTION) by the owner of the vehicle; however, the fix failed to repair the vehicle. The contact stated that the failure had occurred after the recall repair was performed. The manufacturer was not notified of the failure. The failure mileage was 180,000.
NHTSA ID 11731350
Mar 24, 2026 · OH
Fuel/propulsion system
While parked on a slight downhill grade, gasoline started leaking and created a significant puddle on the ground. No warning lamps, messages or other symptoms. An independent service center ran numerous tests over two days, including a smoke test. Diagnosis: There is a hole in top section of fuel tank and the fuel tank needs replaced. Recommendation was to not drive vehicle with fuel tank over half full. Due to the potential of leaking fuel in the presence of a hot ignition source increasing the risk of fire, driving the vehicle long distance with defective fuel tank appears to represent an unreasonable safety risk. Unfortunately, the vehicle is currently 300 miles from home. Mazda’s Mexican-made plastic fuel tank specifically required for our vehicle’s VIN is not currently available. (Mazda makes a similar metal fuel tank in [XXX] which will not fit.) Mazda has an estimated three-month backlog in [XXX] for the fuel tank. Still awaiting repair due to lack of availability of the appropriate fuel tank. Major safety recall NHTSA 16V684000 for the 2015 Mazda3 addresses a manufacturing defect where a fuel tank weld could fail, leading to fuel leaks and a potential fire. Recall is for vehicles produced between 12/4/13 – 9/18/15. Our vehicle was manufactured 02/2015 in [XXX] . However, recall is limited to three specific series of VINs and our vehicle falls in the gap between subject VIN ranges. A recent NHTSA complaint XXX (1/27/26) has the same issue: fuel tank leak, but not within range of recall VINs. It seems that the list of affected VINs included in recall 16V684000 should be expanded to include additional Mexican manufactured vehicles potentially with the same issue. Or create a new recall. Having a hole in the top of a plastic fuel tank securely mounted to the vehicle is unexpected through normal wear and tear. Any fuel leakage increases the risk of fire. NHTSA should investigate if this is due to a defect in Mazda’s manufacturing process. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFOR
NHTSA ID 11726838
Jan 27, 2026 · WV
Fuel/propulsion system
Fuel leaking out of top of tank. Took car to two different shops. They both told me about a recall on the gas tank. They did every test possible and replaced O ring. Even did smoke evap system test. Tank still leaks from the top when full. They said the tank needs replaced. There is a recall for the year make and model but not my VIN?
NHTSA ID 11713563
Jan 15, 2026 · GA Crash
Service brakes
Description On 12-15-2025, in 18°F weather, the vehicle was parked on a residential sloped driveway with the manual parking brake fully engaged. While the driver was outside the vehicle, the parking brake system failed to hold the car’s weight. The vehicle rolled backward, crashed through a wooden railing, teetering on a 4-foot retaining wall, and came to rest over a culvert. Two young children were inside the vehicle at the time of the failure. Component Failure & Availability: The manual parking brake system failed to provide sufficient holding force to secure the vehicle. The rear brake calipers are currently available for inspection. Safety Risk: The safety of the two children inside the vehicle was put at extreme risk due to the unexpected movement of the car. This failure matches the exact conditions and consequences described in Safety Recall 1217F (NHTSA Campaign 17V-393), which states that "unexpected movement of the vehicle if parked on a slope" increases the risk of a collision. Reproducibility & Confirmation: The failure occurred under the specific environmental triggers (cold temperature and slope) identified in the manufacturer's own safety recall documentation. However, the manufacturer has officially refused to authorize the internal teardown of the actuator shafts—the only diagnostic method capable of verifying the rust and sliding resistance that causes this loss of holding force. Inspections: The vehicle has been visually inspected by an authorized dealership and insurance representatives. The manufacturer has declined the necessary internal mechanical diagnostics to verify the internal defect. Warning Symptoms: There were no warning lamps, messages, or symptoms prior to the failure. The parking brake felt fully engaged at the time the vehicle was parked.
NHTSA ID 11711269
Dec 24, 2025 · CA
Engine · Fuel/propulsion system
Catalytic converter keeps giving me check engine
NHTSA ID 11706906
Dec 21, 2025 · CA
Unknown or other
I had purchased a car through Facebook Marketplace after talking to the seller and seeing a CarFax report on the car we decided to purchase it. After coming home the following day I look closer at the documents and realized the CarFax did not match the VIN of the car I purchased. After looking up the CarFax with the VIN on the car I purchased I saw that the person who sold me the car had rolled back the odometer.
NHTSA ID 11706401
Oct 29, 2025 · 86,000 miles · CA
Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (BACK OVER PREVENTION). However, the dealer refused to complete the recall repairs due to the vehicle having a Salvage Title. The contact stated that the rearview camera displayed a black screen while the vehicle was in reverse(R). The contact stated that the failure obstructed the driver's visibility, which prevented the driver from safely operating the vehicle. The manufacturer was made aware of the issue and referred the contact back to the dealer. The vehicle remained unrepaired. The failure mileage was approximately 86,000.
NHTSA ID 11696444
Oct 3, 2025 · OH
Parking brake
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 17V393000 (Parking Brake); and would like to be removed from the recall distribution list. The local dealer and manufacturer were not contacted.
NHTSA ID 11691201
Sep 30, 2025 · CA
Unknown or other
The vehicle automator mileage was changed. The original mileage reading is over 200,000 mi. While the dashboard mileage only reads 90,780 mi. I was unaware of this until I went to the DMV to do a title transfer. The private seller is now nowhere to be found from Facebook marketplace and has blocked me but I do have receipts of everything
NHTSA ID 11690684
Aug 29, 2025 · VA
Electrical system
The Infotainment System will randomly change radio stations while driving, or start scanning through the various system menus, and on at least in one case, started randomly making phone calls from a connected phone. This creates a major distraction while driving. This has been looked at by the dealership and would cost $1500 for the system repair. I understand that this is a known problem.
NHTSA ID 11683859
Mar 10, 2025 · AZ
Power train
1. Automatic transmission suffered a catastrophic failure during operation. Transmission was discarded by Bountiful Mazda, Utah. 2. Both other and I were at risk as the vehicle could not be controlled. 3. I read similar findings on Social Media posts. 4. Bountiful Mazda confirmed metal shavings in the drain trans fluid. 5. No prior warning on car instrumentation, or while driving, or on prior inspection by Cardinaleway Mazda, Gilbert, AZ 6. Neither Mazda USA (Mfr) nor Protective Asset Protection have taken responsibility for the initial equipment failure nor reimbursement through the extended service contract even with extenuating circumstances for late notification. I can provide copies of additional relevant material.
NHTSA ID 11647521
Jan 2, 2025 · FL
Fuel/propulsion system
Since the middle of 2023 I have noticed a gas fume smell both inside and outside of my 2015 Mazda Mazda3 after I fill my gas tank to full. This smell persists up until I use about a half tank of gas or slightly less. I do not top my gas tank off and stop filling when the automatic gas pump stops. There are no visible leaks on or around the gas tank or below the vehicle, and there are no noticeable cracks around the gas tank, valves, lines, etc. Additionally, there are no warning lights present on my dashboard or any codes.
NHTSA ID 11633780
Dec 30, 2024 · IL
Electrical system
The Mazda Connect touch screen in the center display may not accept touch commands properly or may operate by itself (ghost touch). The ITO (Indium Tin Oxide) film of the touch screen may be corroded due to moisture, which may adhere on the lens of the touch screen during the cleaning process at the plant. The corrosion may allow the electrostatic capacity to vary without any input, causing the malfunction of the touch screen.
NHTSA ID 11633180
Nov 2, 2024 · OR
Electrical system
Mazda call this “ghost touch” it happens when the screen starts to act up like crazy, jumping from different audio sources, Bluetooth lose connection, making unwanted phone calls. Almost like a ghost is touching the screen over and over again.
NHTSA ID 11623274
Oct 21, 2024 · VA
Back over prevention › Sensing system › Camera
On Thursday October 9th I drove to work at 11pm and parked my car. I backed up into my space using my back-up camera as I had always did since I had purchased my car in 2019. The next morning when I got home and put my car in reverse to back into my space, I noticed that the back-up camera did not come on. The radio continued to play on the screen, but in never switched over to the camera so that I could use this component to park. After trying several times to try to figure out what the issue was I gave up. I had an appointment that same morning, so I parked my car and came back about an hour later to leave and started my car, pulled out of my space, then put my car in reverse and the camera was back up and running again. I found this to be strange. Most likely this will happen again. I googled/researched this to see if there was a recall for this issue in this make and model and came across a few articles where others had the same or similar complaints. So it all lead me here. It seems as if there is a malfunction in these cameras, if it is happening to others, and happened to me, then it's happening. So what's happening...is my question? Why are these camera not recalled? Do we wait until it shuts down in the middle of us backing up or what? What's next? Can I get someone at Mazda to look at my camera, and replace it? Or is this something I have to live with? I should not have to, neither should I have to pay some outrageous price to get it replace on my own dime. There is definitely an issue with this camera in this make and model. So is anyone going to be fair and do something about this, or wait until there is an accident behind it? If it's a defect in the product, just simply replace it.
NHTSA ID 11620926
Sep 24, 2024 · 60,000 miles · CA
Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact stated that the back-up camera screen image was flickering and became distorted while reversing. The cause of the failure was not determined. The failure mileage was 60,000. VIN tool confirms parts not available.
NHTSA ID 11616156
Sep 22, 2024 · OH
Unknown or other
I am filing this complaint regarding existing Manufacturer Recall Number 6023G (NHTSA Recall Number 23V-487). This recall has been posted since Jul 14, 2023 and the manufacturer has failed to remedy the recall in a timely manner. The remedy is noted on the recall page: "If inspections verify there is image distortion or flickering, the rearview camera will be replaced with a new part and a wiring harness fastening seal will be added." However, the manufacturer continues to state that the remedy is not yet available.
NHTSA ID 11615817
Sep 6, 2024 · CA
Lane departure › Blind spot detection
The contact owns a 2015 Mazda Mazda3. The contact stated that occasionally while the vehicle was shifted into reverse, the review camera image would not display on the digital screen. In addition, the contact stated that the image looked distorted. The contact received a notification of 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was contacted, but the vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 85,000.
NHTSA ID 11613125
Sep 4, 2024 · ME
Unknown or other
The problem I have is with my rearview camera, as described in Manufacturer Recall Number 6023G / NHTSA Recall Number 23V-487. This problem has existed since I purchased the car in November 2022. The recall was announced on 7/14/23. Mazda has failed to provide a remedy. Dealers report that they don't have the parts needed to make the repair and that no remedy has been provided by Mazda. It is meaningless to have a recall if the manufacturer doesn't fix the problem. This is a serious safety issue as when the problem occurs, it is not possible to see behind the car via the camera/screen.
NHTSA ID 11612679
Aug 26, 2024 · 82,000 miles · CA
Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated while reversing, the rearview camera image failed to display. The local dealer was notified of the failure, but the vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure, but no assistance was provided. The failure mileage was approximately 82,000. VIN tool confirms parts not available.
NHTSA ID 11610923
Aug 23, 2024 · NJ
Fuel/propulsion system
Started smelling gas fumes several weeks ago after fill ups at the gas station. Took to my mechanic who diagnosed a fuel tank leak due to rust. No warning lights present. No fuel on the ground or fumes within the cabin.
NHTSA ID 11610399
Aug 4, 2024 · WA
Unknown or other
The infotainment system sometimes has "ghost touches" where random buttons on the screen are pressed without a physical press. This is dangerous because it is extremely distracting to the driver. It often changes songs or calls a random person on my phone contact list. This requires me to quickly and constantly press the "back" button for the infotainment system to prevent it from placing a call. This forces my attention and hands away from the core task of driving while the car is in motion.
NHTSA ID 11606315
Jul 8, 2024 · 63,000 miles · VA
Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The contact stated that while reversing, the rearview camera image was distorted, blank or failed to activate as needed. The local dealer was contacted. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 63,000. VIN tool confirms parts not available.
NHTSA ID 11600126
Jun 27, 2024 · 53,953 miles · NM
Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact stated that while reversing, the rear-view camera image was distorted, black, and failed to appear on the center display. The vehicle was taken to the local dealer, where an unknown software was reprogrammed; however, the failure persisted. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 53,953. VIN tool confirms parts not available.
NHTSA ID 11597244
Jun 11, 2024 · MN
Unknown or other
Mazda opened a recall on the rearview camera not working properly almost one year ago and still has not supplied a remedy. REference: 6023G | Jul 14, 2023 #23V-487
NHTSA ID 11593728
May 22, 2024 · NY
Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.
NHTSA ID 11590087
Apr 29, 2024 · CA
Electrical system
This car's backup camera has been un-usable ~50% of the time, dating back to last year, due to the issue described in the recall. Westcott Mazda refused to inspect and certify the existence of the issue and simply said parts to fix it were unavailable. This recall was issued over 9 months ago.
NHTSA ID 11585934
Apr 1, 2024 · MA
Electrical system · Exterior lighting
Vehicle touch screen has aggressive and persistent “ghost touch” during vehicle operation (while in drive), which should not be possible while in drive at all. This causes any setting or feature accessible through the vehicle “infotainment” system to be activated at random leading to distracting, undesired operation. There is no setting within the “infotainment” system that allows you to disable the touch screen, leading to dangerously distracting situations. There is a voluntary extended warranty period provided by Mazda, but I was not notified required by law, nor was the warranty service offered to me when bringing my car to dealership(s) during the warranty period. Mazda is not willing to pay to fix the acknowledged safety defect.
NHTSA ID 11580498
Mar 12, 2024 · CA
Back over prevention › Sensing system › Camera
See attached document for complaint
NHTSA ID 11576769
Feb 26, 2024 · FL
Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue and confirmed that parts were not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
NHTSA ID 11574083
Feb 14, 2024 · CA
Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was not available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The local dealer was notified of the issue and confirmed that the parts were not yet available. The manufacturer was not notified of the issue. The contact had not experienced a failure. VIN tool confirms part not available.
NHTSA ID 11571865
Jan 18, 2024 · PA
Fuel/propulsion system
strong gas smell in the cabin
NHTSA ID 11566250
Jan 3, 2024 · TX
Back over prevention › Sensing system › Camera
This in regards to NHTSA Recall #: 23V-487. It has been 173 days since this recall was announced and I have not received any correspondence from the manufacturer. The recall has been sitting with no remedy available for 6 months. I want to know when Mazda is expected to have a fix to this vehicle?
NHTSA ID 11563306
Nov 6, 2023 · TX
Unknown or other
My 2015 Mazda is equipped with a touch screen infotainment system. The touch screen has started to randomly change settings when the car is stopped (and running). Since correcting these changes can't be done while the car is stopped (more random changes occur), changes must be made while the car is in motion. This creates a dangerous situation by needlessly distracting the driver.
NHTSA ID 11553749
Oct 27, 2023 · PA
Electrical system
The "infotainment" system, which includes media, navigation, hands-free calling, and the backup camera function, frequently malfunctions. The system will either freeze, or it will execute button presses on its own. The result is that it will change audio selection, make hands free calls via the connected phone, etc. on its own with no driver interaction, which is distracting while driving and could and has caused hazardous driving conditions. While I am listing the most recent occurrence in this form, this has been occurring on nearly every drive for the last 2 years. This typically happens in stop-and-go traffic. The vehicle has a manual transmission and the movement in the center console caused by shifting may be causing loose electrical connections to be disturbed and contribute to the behavior.
NHTSA ID 11552163
Sep 28, 2023 · 67,000 miles · NY
Back over prevention
The contact owns a 2015 Mazda Mazda3. The contact stated that on numerous occasions after he opened and closed the trunk of the vehicle or while shifted into reverse, the rear-view camera image intermittently became distorted or blank. The contact then received notification of NHTSA Campaign Number: 23V487000 (Back Over Prevention) however, the part to do the recall repair was not yet available. An undisclosed dealer was contacted and stated to the contact that there was no such recall for the failure. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was approximately 67,000. VIN tool confirms parts not available.
NHTSA ID 11547192
Aug 30, 2023 · NC
Electrical system
1. IT IS AVAILABLE FOR INSPECTION 2. THE INFOTAINMENT SYSTEM CUTS OFF AN ON AT WILL AND SWITCHES VIEWS WHEN USING THE NAVIGATION SYSTEM WHICH CAN CAUSE YOU TO BE DISTRACTED WHEN DRIVING,ESPECIALLY IF YOU'RE DRIVING IN AN UNKNOWN AREA. 3. VEHICLE HAS BEEN SEEN BY THE MAZDA DEALERSHIP WHICH REFUSES TO REPAIR EVEN THOUGH THIS IS A KNOWN PROBLEM WITH THIS MODEL AS WELL AS OTHER MODELS. 4. NO WARNINGS, JUST STARTED CHANGING SCREENS ALL THE SUDDEN. MAZDA IS WELL AWARE OF THIS PROBLEM AND THE DRIVING DANGERS THAT THIS POSES BUT YET REFUSES TO ADDRESS THE ISSUE. I DID DISCOVER THAT THEY DID ISSUE SOME TYPE OF NOTICE ON THIS BUT IT WAS NEVER A FORMAL WRITTEN RECALL . ONLY FIXED IF YOU TOOK IN AND TOLD THEM ABOUT THE PROBLEM,MOST PEOPLE I WOULD THINK DID NOT DO THIS BECAUSE IT IS COST PROHIBITIVE,THAT SYSTEM COST ABOUT $1400.00 TO REPLACE. THATS NOT POCKET CHANGE FOR MOST PEOPLE.SO WITHOUT A FORMAL WRITTEN MAILED LETTER MOST PEOPLE JUST TRIED TO LIVE WITH IT .
NHTSA ID 11541659
Aug 28, 2023 · WI
Fuel/propulsion system
I was driving 90km and it suddenly stopped, I almost got into it, I put the 4 flashers and I let myself go on the shoulder, then call a towing after a machine test the error code P1092 appears , when I turn on my car, it's so miserable, it starts to bubble, it doesn't want to move forward anymore, lack of strength, All the rest is marked as PASS After googling around, I may have found an answer. Denso, who makes low pressure fuel pumps for a lot of different manufacturers, recalled several million of them a couple of years ago. They determined that there was a manufacturing defect that causes the pump impellers to crack and deform. Then they don't move enough gas to the front of the engine. I guess there is no pressure sensor between the tank and the high pressure fuel pump, so the problem isn't recognized by the car until the sensor in the fuel rail sees it. Several auto makers have issued recalls, including Mazda. But Mazda only went back as far as 2018. Toyota recalled cars as far back as 2013. There are now several lawsuits against various auto makers arguing that Denso knew about the problem in 2015, and the recalls should go further back in time. These two articles do a good job of covering the history of the problem
NHTSA ID 11541303
Mar 28, 2023 · 200,000 miles · LA Fire 1 injury
Engine
The contact owns a 2015 Mazda Mazda3. The contact stated while driving 25 MPH, smoke was coming from under the hood of the vehicle, followed by the vehicle shut down and the check engine warning light illuminated. The contact's son opened the hood and flames came out from under the hood. The contact son burned his fingers but did not seek medical attention. The fire department extinguished the fire. A police report was filed. The vehicle was not diagnosed. The manufacturer was contacted, and a complaint was filed. The failure mileage was 200,000.
NHTSA ID 11514255